Qty (2) 10mm “Quick Release” End Lift Supports 19.45 Extended x 144lbs. Specifications (See below for illustration). Extended Length: 19.45 Inches Compressed Length: 11.89 Inches Shaft End Fitting: Quick Release (Nylon) =10mm=3/8=. 39″ Body End Fitting: Quick Release (Nylon) =10mm=3/8″=. Gas Charged Lift Supports are energy storage devices which create force by compressing gas inside a cylinder. Each support is tested to perform as well as the original units and in many cases to exceed the manufactures specification. Important Notes about Lift Supports. Each support is tested to perform as well as the original units and in many cases to exceed the manufactures specification, please ensure you replace all the supports in the compartment at the same time to ensure proper performance. Our business is lift supports, and we make sure to sell newly produced units, keeping our inventory fresh and rotated. Please take a moment and be sure of what they are actually offering is the Stabilus. We stock several thousand different supports supplied from various quality manufacturers that are not listed here. If we don’t have it we can build many units to your specifications. Special lengths, different pressures or ends, send us the information. Have an existing support with part numbers on it send us any and all numbers that you can find. Depending on the product you are looking at warranties will vary. Lift Supports for the Hood, Trunk, Hatch, Liftgate or Tailgate (None Electrical types). These must be installed in the intended vehicle and the unit stops working properly or to your satisfaction. This policy is subject to change without notice. “Shaft down” is the preferred orientation for mounting a Lift Support. An optimum design would permit the support to be oriented shaft down through its entire actuation. If this is not possible then try to install it so that the shaft is pointing downward in the Closed Position. There are several reasons for this. In order to achieve the damping or “cushion” at the end of the Lift Supports stroke, the piston assembly inside of the Lift Support must travel through oil at the end of the stroke. “Shaft down” orientation ensures that the oil is in the proper location for damping to occur. “Shaft down” orientation ensures that the shaft and sealing components are lubricated with every stroke of the Lift Support. This reduces seal wear and helps to inhibit corrosion. Depending on the application, “shaft down” orientation may reduce the rate of gas permeation through the seal, which increases the usable life of the Lift Support. Some reasons why not to change the orientation of the support. Vehicles with power openers must be installed in the same direction as they came from the factory. Sensors on the door are adjusted to work in the way they were programmed. Installing in the opposite direction can cause them not to work properly. Some models of vehicles do not allow space for the cylinder to be reversed and this will cause a binding when the door or window closes. An example of this is the Ford Excursion Rear Window (or liftgate). Please keep in mind the more often that a cylinder is used the longer it will last. Sitting dormant for any period allows the shaft to bind to the seal and eventually tear. If the application must remain dormant then open the lift supports very slowly the first time they are used. The information provided is Subject To Change Without Notice. Make sure all of your auctions have ended prior to checking out. We accept Pay Pal and Major Credit cards. Please research this before ordering. Please research before ordering. Link at the bottom of this listing. In order to be able to assist you quickly we ask that you supply the following information. B Any and all numbers or markings that are on your old supports. C The part numbers that are on the actual supports that you received. (Not the number on the package but the actual supports). D The year, make, and model of your vehicle and any important details such as Convertible, with or without spoiler, or anything that you think would be helpful. Photos of the issues are great as well. Any items received without authorization are subject to delays and may not receive proper credit. Products that have been damaged during installation or altered will not be accepted. It may take several days to post to your account. Lost Or Damaged Packages: When a package is received damaged, open, or lost in transit we must be notified within 7 days to work with the shipper to correct the issue. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Interior Parts & Accessories\Other Interior Parts & Accessories”. The seller is “mrlousstuff” and is located in this country: US. This item can be shipped to United States, Canada.
- Brand: Lift Supports Depot
- Interchange Part Number: PM3495EZ10
- Manufacturer Part Number: PM3495EZ10
- Vehicle Location: Multi Purpose Lift Support
- UPC: 752785642004